Your Biostar Motherboard does not boot for reasons unknown to you. Don’t be frustrated. This problem can be fixed with the correct methodology. From experience, we understand that your motherboard problem comes from software and hardware issues.
However, user-incurred faults can also affect the motherboard booting process. This article will cover everything you need to know about your Biostar Motherboard problem. By finishing the article, you would have solved the problem with one of the proven troubleshooting methods.
If this sounds interesting, read along as we fix your Biostar Motherboard problem.
Biostar Motherboard Not Booting: Possible Causes
Before we start the diagnosis process, check below some of the common causes of the booting problem in a Biostar Motherboard:
- Low power supply
- Loose or Faulty Cable
- BIOS errors
- Bad external devices
- Faulty motherboard
- Misalign hardware component
Biostar Motherboard Not Booting: DIY Fixes
Troubleshooting your Biostar motherboard doesn’t require much work if you have the correct diagnosis method. Here we’ve provided tested troubleshooting methods to fix the problem. Ensure you follow along till you find the method that solves your problem.
1. Check The Motherboard
First thing first, you need to ensure your motherboard is not defective. Similar to other complex systems, Motherboards are developed with fragile subsystems. It’s possible one of the components might have developed faults. In tight-fitting scenarios, mechanical stress on ports can damage sensitive components.
Even though electrostatic discharge doesn’t deposit physical traces, removal or incorrect connection of a SATA can return obvious physical damages. So, Inspect for physical damage. If you’re a geek, check the motherboard’s integrated circuits for visible faults like scratches.
Do you hear a beep sound during the booting process? You can connect a miniature speaker to your Motherboard speaker port or use a headset during the boot process. If you hear a series of beeps like a morse code, something is wrong with your motherboard.
2. Check The Monitor
If your motherboard gives a single beep, then it’s working fine. So, you should check your monitor and be sure it’s plugged in correctly and powered on. Furthermore, ensure you set the monitor to the correct input and that the cables are not loose or damaged. If there’s any faulty component, you should replace it immediately. Check the brightness level if applicable.
3. Check Power Supply
Your motherboard needs sufficient power, just like your processor and graphics card. A low power supply can result in unbootable scenarios. Ensure the cables are plugged correctly and switched on.
Plug the PC directly into the power source instead of using a socket or power strip. Check the 24-pin and 4-pin power cable, and inspect the connection to ensure it’s appropriately connected to the motherboard.
4. Check The CPU
The Central processing unit is also another component you should run a diagnosis on. Some CPUs do not have inbuilt VGA support. In that case, you’ll need to insert a VGA card to let the system POST adequately. Also, you can disconnect and reconnect the CPU to improve the CPU socket.
CPU incompatibility is another cause of Biostar Motherboard not booting. Ensure you visit the Biostar website to confirm your CPU is listed under CPU support.
5. Disconnect External Devices
The external devices connected can be hindering your Motherboard booting process. One or more of these devices could carry bugs that can cause communication errors or conflicts.
Sometimes, the port you use for the connection can be the one causing the problem. So, unplug all external or USB devices before the booting process. Run the booting process with a keyboard and only connect other devices after.
6. Check The Hardware Inside
Some hardware components inside the computer could have become loose or misaligned. This case usually happens if you transport the computer before the boot process. Open up your computer and remove the panels to inspect that all the components are intact.
Check components such as RAM, graphics card, hard disk, cables, and CPU heatsink. You can unplug all these components and replug them properly, ensuring the connection is tightened.
7. Check Your Hard Drive
There’s a possibility your Hard disk is spoilt or corrupted, thereby resulting in a motherboard booting problem. You should diagnose the hard drive to be sure it’s working perfectly fine. You can interpret this problem as follows:
- Keep pressing the reset button (or F8 in Windows 7) during the boot process to interrupt it and enter the Automatic Repair screen.
- Click on Troubleshoot options and choose the Advanced options
- Click on Command Prompt and search “sfc/scannow.”
- Press Enter key and allow Windows to troubleshoot the drive for corrupt files automatically
- Afterward, Windows will attempt to fix any problem detected.
8. Inspect The BIOS settings
If your motherboard can’t detect any bootable operating system, it signifies that the BIOS is set to boot from the wrong drive. Please check the BIOS settings to determine if it is set to boot from the correct hard drive.
You can jump to the BIOS settings when you keep pressing Esc, F2, or Delete key when your computer attempts to boot. Any changes you’ve modified before the problem should be returned to the original state. Lastly, ensure you disable the Fast Boot feature if you notice the new window update disorganizes the process.
9. Reset Your Motherboard
Your Biostar Motherboard might not be booting because of some software. If you are unable to access the BIOS/UEFI, you can diagnose the problem in three ways as follows:
a. Remove the CMOS Battery
This method is the simplest way to reset your motherboard. Just remove the CMOS, coin-sized battery. Leave it idle for about ten minutes and plug it in again.
b. Jumper Reset
You can also reset your motherboard by applying a jumper for a few minutes. Attach a jumper to the 2 or 3-pin connector of the motherboard. Afterward, gently apply the jumper over the two pins for about 15 minutes.
c. Deep Reset
For the deep reset method, you’re combining the two other ways. Remove the CMOS battery and apply the jumper over the motherboard’s designated portion gently. Leave it overnight so it can drain away all the residual power.
For any of the methods, your Motherboard should reset and boot properly
10. Contact Manufacturers Support
This article comprises comprehensive methods to resolve your Biostar Motherboard boot problem. If none of the methods work for your motherboard, please get in touch with your manufacturer’s support for further diagnosis.